Introduction

With the majority of our renovations complete, I've started an interest in collecting and framing art. My first big big project - original vintage (I think I can say that now) movie poster art.

Where to Buy

• Star Wars - eBay
• Indiana Jones Poster - Alternative to eBay to buy Posters (consistent grading system and more focused products) - http://www.mpb.auction/

Posters with measurements and framing considerations,

Preserving Considerations

After some reading, I concluded it would be a damaging to my authentic movie posters to frame up using traditional backing methods. Let's start with the results,

Glass versus Plexiglass

There are pros and cons for both. Note, if you want to use 3M stickers and not nail in, then Plexiglass is likely your only option.

• Most websites I ran across seem to say plexiglass... but note there may be some bias as these also tend to be websites that sell online and delivery of plexiglass is easier,
  • Hollywood Poster Frames is for plexiglass
  • https://www.postercollector.co.uk/how-to-guides/how-to-frame-movie-posters/
• My local framer The Art Forum recommended glass (he has both) as he feels plexiglass yellows over time - Tony's been in the business a long, long, time  , so I went with Anti-UV, Anti Glare, extra clear glass.

• Used a mat to ensure the glass is lifted off the surface (only possible for smaller than 40"  x 60" posters).
  

Backing the Poster

• Acid-free.
• Acid-neutral.
• Avoid foamcore unless acid free such as Artcare Archival System by Bainbridge which should only be a few dollars more.
  

Linen Backing

• Expensive but preserves, flatten, hides vintage folded posters and allow touchup or outright restoration.
• Make sure to go with professional who will make it reversible.
• For damaged vintage folders can bring up value if resold.
• ~ cost $75 to $150.
• Not advisable for double sided posters.

Here is how it looks after linen backing. It's actually quite thick,

Note, linen backing is really for vintage one-side movie posters. The new modern posted are double-sided to be put into lightboxes. Myself, and the current hobbyist industry is still looking at how to best preserve and frame them.

More Linen Backing,

• Video of how Linen Backing and Restoration Works - http://www.posterfix.com/

• Backing to the Future - Linen Backing in Canada Port Perry, very professional website ( this is who I ended up going with and for low cost storage, you can shrink wrap (ie my Thor Ragnarok poster to keep before framing).
• Linen Backing recommend by mpb.auction, http://www.vintagemovieart.ca/contact-dario-casadei/
• dkartservices - Local West Toronto Linen Backing and custom framing.

PlexiGlass Frames that Can Swap In and Out

I did not go with this, but for those interested here's my research,

• http://hollywoodposterframes.com/ - pre-built frames,
• http://www.spotlightdisplays.com/ - Flip frames (not sure what that means),
• www.displays2go.ca - search for snap frames (also has lightbox models) - not sure if archival though

Putting it Together

Here are things to check with your framer,

• Back the linen poster with acid free material
• Acid free foam core or 4 ply rag are best
• Linen Hinged - Hinge mount using some archival tap stuck to the linen
• Do not stretch
• Trim the linen about 1/8 smaller than the inside dimension of the frame
• If framing with wood make sure to put a barrier if framing to size

Hanging

As these posters are quite large it is very important to hang them properly to not buckle over time,

• Use the D-Rings on the back directly
• Warning - Adding wires to D-Rings for Large posters will put strain on the frame causing corners to pop out.

For how high to hang, it's best to do what the museum's do and go with average eye level ~57 inches for the middle of the poster.

Framing

• The Art Forum - local Framer - weekdays 9-6pm sat 9-4pm

References

• Good Forum Discussions - http://www.allposterforum.com/index.php/board,59.0.html

Inspiration Examples

......

...

...